Multidiscipline Modeling in Materials and Structures: Volume 15 Issue 2

Structural, electronic, and mechanical properties of anatase titanium dioxide: An ab-initio approach

Debashish Dash, Chandan Kumar Pandey, Saurabh Chaudhary, Susanta Kumar Tripathy

The purpose of this paper is to analyze various properties of anatase titanium dioxide (TiO₂) nanoparticles. Further, it proposes to implement Linear Combinations of Atomic…

Fundamental solution of the system of equations of pseudo oscillations in the theory of thermoelastic diffusion materials with double porosity

Tarun Kansal

The purpose of this paper to construct the fundamental solution of partial differential equations in the generalized theory of thermoelastic diffusion materials with double…

Boundary layer flow and melting heat transfer of Prandtl fluid over a stretching surface by considering Joule heating effect

K. Ganesh Kumar, M.R. Krishnamurthy, Rudraswamy N.G.

The purpose of this paper is to study the impact of Joule heating on boundary layer flow and melting heat transfer of Prandtl fluid over a stretching sheet in the presence of…

Board-level vapor phase soldering (VPS) with different temperature and vacuum conditions

Lijuan Huang, Zhenghu Zhu, Hiarui Wu, Xu Long

Vapor phase soldering (VPS), also known as condense soldering, is capable of improving the mechanical reliability of solder joints in electronic packaging structures. The paper…

Approximate static aeroelastic analysis of composite wings

Vladimir Kobelev

The purpose of this paper is to consider divergence of composite plate wings as well as slender wings with thin-walled cross-section of small-size airplanes. The main attention is…

Numerical analysis of steel columns subjected to fire

Yagho S. Simões, Fabio M. Rocha, Jorge Munaiar Neto

Isolated steel columns, when exposed to high temperatures, lose strength in a few minutes due to the high thermal conductivity of its constituent material. When these structural…

Spectral quasi-linearization method for Casson fluid with homogeneous heterogeneous reaction in presence of nonlinear thermal radiation over an exponential stretching sheet

Subrata Das, Hiranmoy Mondal, Prabir Kumar Kundu, Precious Sibanda

The focus of the paper is only on the contributions toward the use of entropy generation of non-Newtonian Casson fluid over an exponential stretching sheet. The purpose of this…

Laser pulses and rotation effects with the temperature-dependent properties in micropolar thermoelastic solids with microtemperatures

Mohamed I.A. Othman, Ramadan S. Tantawi, Mohamed I.M. Hilal

The purpose of this paper is to report effect of rotation of micropolar thermoelastic solid with microtemperatures heated by laser pulses. The problem was solved analytically to…

Study on dynamic characteristics of boom system for balance hoist based on rigid-flexible coupling simulation

Yu Liu, Jie Hao, Zhihua Sha, Fujian Ma, Chong Su, Shengfang Zhang

Aiming at the unbalancing problem of the neutral equilibrium characteristic for balance hoist in the loading process, the purpose of this paper is to establish a dynamic equation…

Effect of non-uniform heat source/sink on MHD boundary layer flow and melting heat transfer of Williamson nanofluid in porous medium

Jayarami Reddy Konda, Madhusudhana Reddy N.P., Ramakrishna Konijeti, Abhishek Dasore

The purpose of this paper is to examine the influence of magnetic field on Williamson nanofluid embedded in a porous medium in the presence of non-uniform heat source/sink…

Dynamic problem in piezo-electric microstretch thermoelastic medium under laser heat source

Arvind Kumar, Praveen Ailawalia

The purpose of this paper is to study the thermal and mechanical disturbances in a piezo-electric microstretch thermoelastic medium due to the presence of ultra-short laser pulse…

Effects of thermal radiation and magnetohydrodynamics on Ree-Eyring fluid flows through porous medium with slip boundary conditions

K. Ramesh, Sartaj Ahmad Eytoo

The purpose of this paper is to investigate the three fundamental flows (namely, both the plates moving in opposite directions, the lower plate is moving and other is at rest, and…

Expected range of the output response for the optimum input parameters utilizing the modified Taguchi approach

Rajyalakshmi K., Nageswara Rao Boggarapu

Scatter in the outcome of repeated experiments is unavoidable due to measurement errors in addition to the non-linear nature of the output responses with unknown influential input…

Numerical calculation of crack width in prestressed concrete beams with bond-slip effect

Jinliang Liu, Yanmin Jia, Guanhua Zhang, Jiawei Wang

The calculation of the crack width is necessary for the design of prestressed concrete (PC) members. The purpose of this paper is to develop a numerical model based on the…